Recent Posts

Pages: [1] 2 3 ... 10
1
I forgot to add a list of names that are on the wires.
2
Technical Support / Re: Main 12 volt fuse panel location
« Last post by Vince Toscano on November 13, 2026, 04:50:09 PM »
The running lights are part of the chassis electrical system. That all comes from the front run bay, outside below the driver seat. I would start there. I don't know if you have large multi wire connectors. That is where I found many problems in my 2003 Beaver Marquis.
3
There are kits available with tools for cleaning and/or replacing male and female pin connectors.  The kits vary in features and content.  And electronic cleaning fluids as others note;  spray on ones, like CRC Electronics Cleaner, can be handy but messy in confined spaces, so I often use DeoxIT D100 in the 7.4ml bottle for dissolving small electronic corrosion.  Then brushes and swabs as appropriate, followed by light applications and wipe of the DeoxIT for preventive purpose.  Corrosion-X can stave off problems on exposed metals and connections as well.


Joel

4
Motorhomes and Tow Cars / For Sale: 2006 Beaver Monterey Laguna IV
« Last post by Robert Buterbaugh on November 11, 2026, 06:16:54 PM »
2006 Beaver Monterey Laguna IV - 41 foot, 4 slides, king bed, stackable washer/dryer, 1-1/2 baths, theater seating, custom computer workstation, Cat C-9 400HP coach in excellent condition. 71,000 miles. Upgrades include new tires and windshield 2023; two Dometic AC/heat pumps 2024; 4 new slide toppers, two new Flat screen TVs, Hydrohot refurbished, roof waxed and resealed 2025. Since 2023, this coach has been professionally winterized and de-winterized each year including annual battery service and inspection of AC/heat pumps, hydrohot heating system, generator, plumbing, slide and electrical systems. Oil change and air dryer service performed. Acquired in 2024, we are trading down to a smaller size coach.

Serious inquiries only at megpope916@gmail.com

Thanks, Bob & Megan Buterbaugh
Farmingdale, NJ

Posted 11/11/2026
5
The Valid Power Gear Service Manual is in Coach Assist under Leveling Systems. Pages 50 to about 65 show the connector wiring with signal names and wire colors.
Steve
6
Thanks for the cleaning information, I will do that eventually.  Everything is working properly right now so I don't think I will fix it until it breaks.
7
My Power Gear (Valid) AIR ONLY system is NOT allowing Auto Level mode, just beeps. Manual control of the bags and travel mode are fine. The dash parking indicator is on BUT there is NO Park indication on the Valid control board arm rest panel. So I want to trace which wire is supposedly sending the Park Brake signal to the control board to see if I have a bad trace on the "obsolete" control board, or if there's a wiring problem in the harness going to the control board. I can't find anything online that definitively shows the pinouts of the 8 pin connector. AI searches is giving me a lot of conflicting information.  What are the pinouts on this connector? Also, where is the Nason switch located (I don't see it around the parking brake valve.) As I have the Park indication on the dash, I think the Nason switch may be okay, but maybe there are different wires to the dash and to the Auto Level control panel.

Attached are pictures of my 8 pin connector.  I may have found a constant 12V power and a ground, but don't seem to find what should be the switched ignition source, and don't seem to have another ground.  AI seems to be inconsistent if the transmission neutral wire would be 12v or ground.  (Coach starts fine, and transmission pad shows N thus a tranny neutral signal seems to be okay.  Shifting from neutral to drive shifts the pad to Travel mode.  If the pad is powered down turning on the ignition powers up the panel thus I believe most of the panel is working correction.) So, it would be very very helpful if I knew what pins (or color wires) have what function.  Since the pad does NOT indicate "PARK", I think that is my problem preventing it going into Auto Level mode.

2007 Patriot Thunder, Air Only (No jacks)
8
Technical Support / Re: 12 VDC, Front Run Bay Electrical power Chassis-Dash Controls
« Last post by Carl Boger on November 10, 2026, 11:34:35 PM »
David,

When mine started acting up I used electrical contact cleaner along with small round soft bristle brushes and mig welding tip cleaners along with carb jet cleaners.  After scrubbing everything a couple of times I put a dab of dielectric grease on the tip of the pins and then on both sides of the connectors forming a water tight seal.  I did this to all the plugs below the drivers seat area.
That repair worked for me for close to 9 years until I recently sold the MH, and as far as I know it is still working.   Hopefully yours can be repaired as successfully.
9
Hi David,
Yes the photo of the connectors are bad. Did they look at the other 3? There are 2 more in the upper right corner. These are of a different type more on the marine style because they have internal and external seals. When I took those apart all I did was cleaned them with electronic cleaner. The one that has the majority of the wire you may have to replace the o-ring. I did because the o-ring was deformed.
10
Here are photos of the bay and the offending connectors.  The corrosion was caused by a leaky drivers window which REV RV Group repaired. Its hard to believe they are still working.
Pages: [1] 2 3 ... 10