BAC Forum

General Boards => Technical Support => Topic started by: Bob Morgan on July 29, 2021, 07:05:01 PM

Title: Alladin tank calibration.
Post by: Bob Morgan on July 29, 2021, 07:05:01 PM: Howdy,

I’m new here. I recently bought a new-to-me 2003 Beaver Monterey 37 Seacliff With Cummins 8.3/Allison 3000. I’m having trouble calibrating the Tank Status. All tanks show 255 even though they’re currently empty. The tank calibration screen will not allow me to change anything or input raw data values. I have no other tank monitor so I’m stuck. Ideas?

Thanks

Bob
Title: Re: Alladin tank calibration.
Post by: Lee Welbanks on July 29, 2021, 07:59:35 PM: Bob, The tanks are pretty easy to set up, here is a video by AZ Expert changing sensors and re-cal the system to read correctly.https://www.youtube.com/watch?v=ToJz9LifIuI&ab_channel=AZExpert
Title: Re: Alladin tank calibration.
Post by: Bob Morgan on July 29, 2021, 08:32:18 PM: I watched the video but my system is older and as I mentioned it will not allow me to change the values on the calibration screen.
Title: Re: Alladin tank calibration.
Post by: Steve Huber Co-Admin on July 29, 2021, 09:21:05 PM: The 2003 Aladdin Tank Level Interface Module Calibration Procedure is located in Coach Assist along with a number of other Aladdin procedures and manuals.
Steve
Title: Re: Alladin tank calibration.
Post by: Lee Welbanks on July 29, 2021, 11:20:43 PM: Quote from: Bob Morgan on July 29, 2021, 08:32:18 PM
I watched the video but my system is older and as I mentioned it will not allow me to change the values on the calibration screen.

Are you able to get to the screen where you enter the code to unlock the system? Another thing you might try is reboot you Alladin somewhere in the coach there will be a switch to turn off the power to the system.
Title: Re: Alladin tank calibration.
Post by: Bob Morgan on July 30, 2021, 01:58:47 AM: Quote from: Steve Huber Co-Admin on July 29, 2021, 09:21:05 PM
The 2003 Aladdin Tank Level Interface Module Calibration Procedure is located in Coach Assist along with a number of other Aladdin procedures and manuals.
Steve

Where is the Coach Assist section? I’m still finding my way around here. Thanks.

Bob
Title: Re: Alladin tank calibration.
Post by: Frank Bergamo on July 30, 2021, 02:10:04 AM: Bob,

Under updated topics, click on Private BAC Members only, you will find what you need. Hope this helps.
Title: Re: Alladin tank calibration.
Post by: Steve Huber Co-Admin on July 30, 2021, 03:20:46 AM: Bob,
Log in on the BAC Club website at https://www.beaveramb.org/
Select the Technical tab and you will see the Coach Assist link.
Steve
Title: Re: Alladin tank calibration.
Post by: Keith Moffett on September 06, 2021, 07:38:44 PM: Quote from: Lee Welbanks on July 29, 2021, 07:59:35 PM
Bob, The tanks are pretty easy to set up, here is a video by AZ Expert changing sensors and re-cal the system to read correctly.https://www.youtube.com/watch?v=ToJz9LifIuI&ab_channel=AZExpert
Good video.
Title: Re: Alladin tank calibration.
Post by: George Harwell on September 07, 2021, 02:09:14 PM: Bob, George Harwell here, 03 Monterey Seacliff. Call me at 405 642 0389 and I'll try to walk you through it. The black and gray sensors are buried behind the water bay panel so we will concentrate on the fresh tank first. That sensor is normally OK. If we can get the system working with fresh water then we can proceed to the next. The fresh tank is in the second bay forward of the right rear wheels.