Recent Posts

31

Technical Support / Re: Onan generator 7500

« Last post by Randy Keaveny on April 21, 2024, 04:08:49 PM »

Thx.  I got it to run.  But does not sound right.  As it surges.   Starts up.   Runs.  Takes the load. Then ki da struggles to keep running.  No codes now.  But. Something is still not right.  Internal fuel filter that I cannot see ??   Is what I am wondering now.

32

Technical Support / Re: Aladdin calibration

« Last post by Eric Maclean on April 21, 2024, 02:43:57 PM »

Thanks Steve good to know
Eric

33

Technical Support / Re: Aladdin calibration

« Last post by Steve Huber Co-Admin on April 21, 2024, 12:59:38 PM »

Thx, Eric.
This is also available in the Video Links post on the Private BAC Members only board.
Steve

34

Technical Support / Re: Onan generator 7500

« Last post by David T. Richelderfer on April 21, 2024, 10:29:20 AM »

Our generator is a different model but I believe the fault codes are very similar for all their models.  I found the following.  It indicates you should be able to get a second-level fault code which would more precisely define the generator's issue.

"• Three blinks indicate a service fault. Press Stop once to cause the two-digit, second-level fault code to blink. (Pressing Stop again will stop the blinking.)The two-digit code consists of 1, 2, 3, 4 or 5 blinks, a brief pause, and then 1 to 9 blinks. The first set of blinks represents the tens digit and the second set of blinks represent the units digit of the fault code number. For example, Fault Code No. 36 appears as: blink-blink-blink—pause—blink-blink-blink-blink-blink-blink— long pause—repeat"

35

Technical Support / Re: Replace Domectic Air Conditioner

« Last post by Carl Boger on April 21, 2024, 12:31:38 AM »

Lawlor,

It probably will not be a simple plug and play, but will have individual color coded wires that have to be put into the correct positions.  There is usually enough slack in the wire to make this a fairly easy connection.

36

Technical Support / Re: replacing brake lines on a 1998 Beaver Patriot Savannah.

« Last post by Carl Boger on April 21, 2024, 12:21:22 AM »

Eric,

This job is pretty much straight forward brake work but the working quarters are tight.  Now I am a fairly fit, fairly low body fat,(15%) person, but I am 6'1" and 220 lbs so I don't fit well in a lot of places. I also have a repaired shoulder that doesn't do well with overhead work.   If your generator is on a front slide than run it out that helps a lot.  The higher you can get the coach also helps!  I drove up on ramps raising the coach 4.5 inches, 6 would have been even better, 12 would have been great. 

This job is doable, but take your time and break it up into small segments.  I was sore for a week after I finished, probably should have slowed down the work but I tend to force my way through.

Hopefully you will git a tip or two out of this,

37

Technical Support / Onan generator 7500

« Last post by Randy Keaveny on April 20, 2024, 10:20:50 PM »

Hi all. Back at  the motorhome working on genset.  Showing a code of 3 flashes. But will not start. It fires.  Like it wants to.  But will not grab.      Plenty of fuel.  Is there a shutoff accessible.      Or way to get to injectors.     The rapid flashes for pre heat  glow plugs is working.   And I can hold button down to hear it prime.   Any help

38

Technical Support / Replace Domectic Air Conditioner

« Last post by Lawlor Wakem on April 20, 2024, 10:12:25 PM »

We need to replace our front rooftop air conditioner on a 2004 Beaver Marquis.  The original air conditioner was Dometic  part #630515.321.  Dometic gave us part number 651815-HXX1J01 The Dometic Penguin II with Heat Pump.  We also bought a new 10 button thermostat.  Will the wiring harness and plugs be the same as the old air conditioner or will there need to be adjustments made?  Thank You. 

39

Technical Support / Re: replacing brake lines on a 1998 Beaver Patriot Savannah.

« Last post by Eric Wallace on April 20, 2024, 08:11:35 PM »

Thanks so much for the quick reply, Eric.
My local FleetPride has that caliper part number in stock. 
I'll verify with them the material of the pistons.
After re-reading all the brake problem posts on this forum it appears the
problem with the phenolic pistons is that water in the system causes them to swell.
A periodic complete purge and refill with new fluid should help that situation if I
can't find anything but phenolic pistons.
Again, thanks for all the information.
Eric

40

Technical Support / Re: replacing brake lines on a 1998 Beaver Patriot Savannah.

« Last post by Eric Maclean on April 20, 2024, 07:11:46 PM »

Eric
There are a lot of things that can cause the brakes to smoke any of the below can contribute to a tight brake .
1) although technically no a brake problem and hub seal leak can cause smoking and burning
2). Bad or overheating wheel bearings can contribute to number (1).
3) as you described phenolic brake caliper pistons can absorb moisture and swell in their bores.
4) incorrect brake fluid can cause caliper seals to swell and hold caliper piston/s extended.
5) bad or incorrectly installed caliper seals.( During caliper rebuild )
6) moisture the brake fluid causing rush with in the calipers ( the lowest point in the system)
  CAUTION moisture also lowers the building point of the brake fluid and can lead to brake fluid boiling and brake failure.
7) caliper slides too tight or not maintained or cleaned properly.
bad brake flex lines ( as they get old the inner lining can collapse causing the flex line to work like a check valve holding pressure on the caliper.
9) a bad master cylinder or poorly adjusted master cylinder actuator rod can cause the master cylinder piston to not return back far enough to uncover the compensator port in the master cylinder causing the brakes to drag ( worst when they are hot as the fluid expands has no where to go and applies
 pressure to the caliper)
10) on an air over system the treadle valve ( brake pedal) may be sticking and not releasing the brakes fully ( the pedal itself will sometimes get seized)

With that said I assume you have air over hydraulic brakes on your coach ( correct me if I'm wrong ) it may be hydraulic over hydraulic.
The easiest way to diagnose a hydraulic problem is to loosen a bleeder screw when the problem is exhibited if loosening the bleeder screw allows the wheel to turn freely the problem is likely a flex line or master cylinder and not the caliper itself
Your front brake system will have three flex lines one at each front wheel and one at the master cylinder for the front brakes .

Most of these parts are off the shelf parts used on medium duty trucks of the era ( Ford , International , Freightliner.)

BRAKE PARTS
Front wheel bearing    inner=  Bower #HM212049X
                                       Outer=.Hyatt. #3782
                             Outer race=. Hyatt  =3720
Brake flex lines.          Front=  Raybestos. #BH383373. = 42"
                                                    Raybestos  #BH381081. = 40 1/2 "
                                                   Raybestos   #BH381082  =  39 "

Front hub seal.                   =   stemco #383-0136

Front brake rotor.               =  Centric  12079023

Front brake calipers          = centric #14179001. Or Bendix #55252.   ( Note calipers are same right and left and front and rear)
Front caliper hardware kit= centric #11779003  ( this is the guide spring and wedge kit for the caliper mounting) does one axle or two calipers.

Front brake pads.             = centric #10602360.   Or Dayton D236

Front brake converter with master cylinder = Haldex # N37216c

Below is a link to the centric caliper which states the piston material is steel { I'd assume stainless steel )

https://www.showmetheparts.com/centric-parts/centric-14179001.html


Hope this helps
Eric