Author Topic: Scan Gage 2 install  (Read 1717 times)

Rick Penick

  • Guest
Scan Gage 2 install
« on: January 01, 2022, 09:23:37 PM »
Trying to install a scan gage 2 on my 97 monterey..
So i see diagnostic port in the back but shouldn't there be a port under the dash? I looked don't see it. Appreciate any input.

Thanks
Rick

Joel Ashley

  • BAC Member
  • *
  • Posts: 2341
  • Thanked: 801 times
  • OSU Class of '73, Oregon Native. RVing 39 years
Re: Scan Gage 2 install
« Reply #1 on: January 02, 2022, 12:20:14 AM »
If your coach has an access panel in the top of the dash in front of the steering wheel, like ours it may be in there.

Joel
Joel and Lee Rae Ashley
Clackamas, Oregon
36.9 ft. 2006 Monterey Ventura IV, aka"Monty Rae"
C9 400HP Cat

Carl Boger

  • BAC Member
  • *
  • Posts: 433
  • Thanked: 132 times
Re: Scan Gage 2 install
« Reply #2 on: January 02, 2022, 12:57:22 AM »
On my 1998 Patriot it is on the Drivers Side under the steering wheel at the bottom of the dash panel.  If you can not see it it my be tucked up under the dash some.
Carl

98 Beaver Patriot Savannah
330 hp Cat 3126

Rick Penick

  • Guest
Re: Scan Gage 2 install
« Reply #3 on: January 02, 2022, 02:00:53 PM »
 Ok thank you for the reply the scan 2 has adapter for to configerations it is round and according to their instructions it has a cap covering it and is obviously round. Will check after we get home from church see if i can locate it.


RP

Paul Meehan

  • BAC Member
  • *
  • Posts: 111
  • Thanked: 42 times
  • Travel with DW and two K9's
Re: Scan Gage 2 install
« Reply #4 on: January 02, 2022, 02:13:59 PM »
On my 2001 Patriot my ECM diagnostic port was, as Carl stated, behind dash more centrally located behind dash radio.  I laid on my back in front of driver's seat looked up and towards the radio and there it was.

I was able to free it up by snipping a few zip ties and pulling it down for better access.  It was a 6-pin diagnostic port (1990's to early 2000's).  Not the newer 9-pin (early 2000's to present).
Good luck!
Paul and Peggy
St. Johns, Florida
2001 Patriot Ticonderoga 37' 2 Slides (2015-2019)
2014 Newmar Dutch Star 4369 (2019-Current)
2021 Jeep Grand Cherokee  Limited

Dave Atherton

  • BAC Member
  • *
  • Posts: 1015
  • Thanked: 877 times
Re: Scan Gage 2 install
« Reply #5 on: January 02, 2022, 11:56:33 PM »
Gentlemen, my suggestion be very careful using the Caterpillar data port when install aftermarket
Equipment into that diagnostic port. The 12 volt wires from the data test port are un fused and if
something is not correct with the aftermarket equipment being used at this port you will be replacing
the engine ECM . This is being a common problem as time goes on with several failures with engine
ECM. Dave Atherton Retired Cat Mechanic
The following users thanked this post: Joel Ashley, Paul Meehan

Rick Penick

  • Guest
Re: Scan Gage 2 install
« Reply #6 on: January 09, 2022, 12:05:33 AM »
 Dave here is what i have under my dash a 12 pin diagnostic port. scan guage sent me the proper cord for my motor home after they looked it up and and i sent them a picture of the port. Will this affect the ECM in anyway? i plan not to mess with the one in the service bay you used when you plugged your computer into my motor home when we met in Showlow.

thanks
rick