BAC Forum
General Boards => Technical Support => Topic started by: Rick Daniels on August 02, 2023, 10:00:46 PM
-
The entry door into my "99 marquis requires a pry tool coming in or a knee bump going out. I have determined that the whole door has dropped around 1/8". If I lift the door up in operates normal. The hinge looks like a giant piano hinge. There are two gaps in the hinge (see pictures). one high and one low. It appears at one time that there may have been some kind of a spacer in those gaps. Can someone with a similar hinge, or knowledge, tell me if there is some kind of a spacer that goes into the wide gap? If so, that would cure my problem.
-
Any Marquis 1996-2001 should have the same hinge
-
Rick,
If the door needs to move up 1/8 of an inch I would try putting a shim under the bottom of the hinge and then bend and epoxy it in place. Just raise the door high enough it high enough to operate correctly. Hopefully this will help some.
-
Rick
Does the door drag on the threshold or the latch pin ?
The latch pin is supposed to float to allow it to align.
There is a door adjustment manual in the coach assist section for the TDL doors.
Hope this helps
Eric
-
Hi Rick. I have the same hinge on my Marquis. I have tried a couple of fixes.
That hinge is stainless steel, when it was new there were two nylon spacers in those two gaps in the hinge that kept it aligned and not wearing on its self. There is or should be a rolled pin in the bottom of the hinge that that keeps the hinge pin in place. First your gonna have to lift the door and measure for the spacer that you need to correct the door alignment. Then You will have to drive that rolled pin out. Then you can grab the hinge pin through the bottom open space with Vice grips and tap it down gently a little at a time until it clears the upper space. With the upper space clear you can fit a brass bushing into that space. Bushing are available at most hardware stores. The bushing should have 3/8, ID and about 1/2, inch OD about 1 inch long. I add a flat washer to to ether the top or bottom of the bushing. I have to use a grinder to get that bushing to the right height to make your correction. Now for the hard part. Lifting that door and slipping that bushing into place and tapping the hinge pin back into place. The best way to lift the door is to buy a product called (Winbag) its an inflatable tool made just for this type of work. Remember to be gentle when hitting on the hinge pin. This is a little long winded. If you have questions you can call me 805-975-5314.
-
https://www.amazon.com/Winbag-15730-Wedge-Alignment-Inflatable/dp/B00NESAU0U/ref=asc_df_B00NESAU0U/?tag=hyprod-20&linkCode=df0&hvadid=309789102684&hvpos=&hvnetw=g&hvrand=8117533743305911531&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=1024458&hvtargid=pla-383709888401&psc=1&tag=&ref=&adgrpid=60439547983&hvpone=&hvptwo=&hvadid=309789102684&hvpos=&hvnetw=g&hvrand=8117533743305911531&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=1024458&hvtargid=pla-383709888401
Also: https://www.amazon.com/Rhino-Strong-Professional-Grabber-Marring/dp/B083H44VBH/ref=asc_df_B083H44VBH/?tag=hyprod-20&linkCode=df0&hvadid=563727898715&hvpos=&hvnetw=g&hvrand=8117533743305911531&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=1024458&hvtargid=pla-1639929077980&psc=1
I got one of these this spring to help lift our washing machine, and slip some glides under its front feet so I could move it from its “cranny” and regularly service its hose connections. It works pretty doggone well. Everyone should have one or two in their tool arsenal. It makes it easier if the feet on a fridge, freezer, or other heavy appliance require adjustment.
Joel