BAC Forum
General Boards => Technical Support => Topic started by: Craig Rollins on May 12, 2012, 02:41:26 AM
-
Today my wife was in the bedroom when I heard her call the word(?) "Oh-oh". This is never a good thing, so I went to investigate. When I entered the room she pointed to the floor in the corner. Under the TV and in front of the closet was a self tapping hex head screw. I've looked all over that corner and can't figure out where it may have come from. Yesterday we moved the coach about 130 miles and I'm thinking that the screw may have fallen out of the back side of the bureau slide behind the TV but I can't see in there to be able to tell where it goes. Does anyone have any suggestions? I've attached a pic (I hope) with a steel rule for scale.
-
I have seen this type of self tap screw on the slide brackets. You would need to pull the trim and look at the top slide support. I had to use a larger screw because the hole was elongated. The slide hangs from the mechanism and was popping just before it opened and closed against the body. Need to get it checked or do it yourself soon. I waited to long and had to put rollers under the slide to support the weight.
-
Thanks for confirming my own suspicions Jim. I'll pull the trim Sunday and take a look.
-
Craig,
It would be a good idea to check your slide hardware, however do not be surprised if you can not find out were the screw belongs. The assembly line workers dropped many screws when they were building your coach and they rarely if ever picked any of them up. My coach is twelve years old and I am still finding loose screws that when you look closely at the head they were obviously never installed in anything.
Gerald
-
I find these all the time loose in my bedroom (much like my head). Like Gerald said many are dropped during assembly never to be seen until years later when they get raked out into the bedroom floor by the slides. I did discover however that the rollers supporting the bed on that slide were missing two of these type self tapping screws so when you are checking be sure to check the rollers that support your slideout. It could save you a lot of grief in the future. BTW that screw appears to have the threads stripped which means it could have been over-tightened when it was installed. Don't be surprised if you don't find where it came from.
-
Worst moments on a sailboat is when a screw lands on the deck. If there is nobody alongside who mischevously tossed the screw against the sail, there will be a serious problem in the immediate future. Hope yours was from a worker at the time of assembly.
-
Worst moments on a sailboat is when a screw lands on the deck. If there is nobody alongside who mischevously tossed the screw against the sail, there will be a serious problem in the immediate future. Hope yours was from a worker at the time of assembly.
reminds me of when I was racing....tossed a cotter pin or screw (well used) into more than one cockpit.
Young and foolish then, now just foolish.
-
Well, the mystery has been solved. It is definitely a screw that fell out of the slide mechanism where it attaches to the slide. This may have been a blessing in disguise because it revealed a number of other loose screws. We are currently in Bend at BCS and the screw has been replaced and the loose ones have been tightened.
When we got here we parked and put the slides out. When we put out the kitchen slide the Tambor Door promptly destroyed itself. Thankfully BCS had one in stock. Had we been anywhere else in the country we would have probably waited days while hunting down a replacement.
Thanks again to all who responded. I believe we're in good hands.
-
Definitely, Craig. Ken and his crew will treat you right ;). You might have them inspect your other slides also for potential problems like guide roller wear and alignment, and lubricate their mechanisms like they did for me a couple weeks ago.
Joel
-
We were recently at Bend for repairs that were supposedly done at the Monaco service center in Minnesota. Shawn and the guys really know what they are doing. Most of what was done in MN had to be redone, and now everything works great!!! Also had them install a monitor to the toad while the engine data is displayed on the Alpine.