Author Topic: Essex Keyless Entry  (Read 3763 times)

Bobby Kirk

  • BAC Member
  • *
  • Posts: 144
  • Thanked: 15 times
Essex Keyless Entry
« on: January 25, 2025, 04:26:29 PM »
I have a 2006 Beaver Marquis     The system lost the code to open door while it was sitting in storage.  I have changed the
code many times since i have owned it all its life.  When I try to change the code (press button it beeps then i put in 1119
when i press the 9 it beeps like 4 times and will not accept new code) could it b the key pad??  have unpluged  to see if would 
reset.  no luck   Any help would b appreciated



Bobby Kirk
2006 Marquis

Bryan Beamon

  • BAC Member
  • *
  • Posts: 382
  • Thanked: 134 times
Re: Essex Keyless Entry
« Reply #1 on: January 26, 2025, 06:44:21 PM »
Bobby, call Tri Mark and they will send you a hard reset procedure to establish a new set of codes. Their tech support # is 800 447 0344 ext 1072
C & Bryan Beamon
2006  to present
2007 Contessa 42ft Cat C-9 400hp
1996 to 2006 97 Beaver Patriot Camden

Bryan Beamon

  • BAC Member
  • *
  • Posts: 382
  • Thanked: 134 times
Re: Essex Keyless Entry
« Reply #2 on: January 26, 2025, 06:47:49 PM »
Wrong # it should be 800/447/0343
C & Bryan Beamon
2006  to present
2007 Contessa 42ft Cat C-9 400hp
1996 to 2006 97 Beaver Patriot Camden

Bobby Kirk

  • BAC Member
  • *
  • Posts: 144
  • Thanked: 15 times
Re: Essex Keyless Entry
« Reply #3 on: January 27, 2025, 05:38:13 PM »
Thanks Bryan for the info   I will give them a call.

Bobby Kirk
2006 Marquis

Bobby Kirk

  • BAC Member
  • *
  • Posts: 144
  • Thanked: 15 times
Re: Essex Keyless Entry
« Reply #4 on: January 27, 2025, 05:51:47 PM »
HI BRYAN   Called Tri-Mark they do not make the Essex system only Tri-Mark so I am back to square one. anyone have
ideas would appreciate them.

Bobby Kirk
2006 Marquis

Steve Huber

  • Administrator Group
  • *
  • Posts: 3699
  • Thanked: 1602 times
Re: Essex Keyless Entry
« Reply #5 on: January 27, 2025, 06:15:06 PM »
Bobby,
We have Essex manuals in Coach Assist.
Steve
Steve
Coachless
2015- 6/24  07 Contessa Bayshore C9,  400 hp
2013-2015: 00 Marquis Tourmaline, C12, 425 hp
2005-2013: 01 Contessa Naples, 3126B, 330 hp

Bobby Kirk

  • BAC Member
  • *
  • Posts: 144
  • Thanked: 15 times
Re: Essex Keyless Entry
« Reply #6 on: January 28, 2025, 01:33:34 AM »

Thanks Steve  I have the Essex Manual   Have a call in to them waiting for call back 


Bobby Kirk
2006 Marquis

Bobby Kirk

  • BAC Member
  • *
  • Posts: 144
  • Thanked: 15 times
Re: Essex Keyless Entry
« Reply #7 on: January 29, 2025, 12:58:02 AM »
Does anyone know if Essex has a hard reset procedure for the keyless entry system.. Have called Essex  No return call
called BCS and no call back   will keep trying 

Bobby Kirk 
2006 Marquis

Gene Obie

  • BAC Member
  • *
  • Posts: 156
  • Thanked: 36 times
Re: Essex Keyless Entry
« Reply #8 on: January 29, 2025, 03:14:08 AM »
I got the hard reset procedure listed below from chatGPT - but buyer beware as sometimes it's wrong.

I believe I read where the system stores code in non-volatile memory. So the fact that it "lost" the code in storage sort of seems to me the keypad may have failed (memory/cpu failure). When you say you removed the connector to cycle power - did you remove the keypad on the outside or just disconnect the connector near the programming switch? I'm assuming you tried the 1 3 5 7 9 master code after you power cycled? Also, when you say there are 4 beeps after 1119 is the 4th a long beep? If so, I believe the manual indicates system error.  If you haven't removed the keypad you might take a look to see if there's wiring damage or signs of excess heating on the backside. I have no idea if the reset procedure below is valid - but since your system seems dead anyhow it probably can't hurt.

Unconfirmed!! procedure from ChatGPT

Factory Reset Procedure for Essex KE-1701:
Power Off the Keypad

Disconnect power from the KE-1701 by removing the power source.
Enter Reset Mode

While holding down the [1] and [3] keys, restore power to the keypad.
Wait for Reset Confirmation

Continue holding the keys for about 10 seconds until you hear a confirmation beep or see an LED indication (if applicable).
Release the Keys

The keypad should now be reset to its factory default settings.
Reprogram the Keypad

Since the reset erases all user codes, you’ll need to reprogram access codes as needed.
-Gene

2005 Beaver Marquis, Ruby 40, C-13 Cat 525HP, Allison 4k
Towing 2018 F-150
Washington

Bobby Kirk

  • BAC Member
  • *
  • Posts: 144
  • Thanked: 15 times
Re: Essex Keyless Entry
« Reply #9 on: January 31, 2025, 12:26:33 AM »
Hi Gene   Thanks for the info and will keep in my notes  I finally got to talk to a human a Essex and he was very helpful
walked me thru procedure and every thing is now working  Thanks for the help 

Bobby Kirk
2006 Marquis

Randy Stephenson

  • BAC Member
  • *
  • Posts: 68
  • Thanked: 8 times
Re: Essex Keyless Entry
« Reply #10 on: January 31, 2025, 10:02:09 PM »
Bobby:

Can you outline what the steps were from Essex?
Randy & Jane Stephenson
2004 Beaver Patriot Thunder
Lexington 40' 3 Slides
CAT C12 505 HP

Bobby Kirk

  • BAC Member
  • *
  • Posts: 144
  • Thanked: 15 times
Re: Essex Keyless Entry
« Reply #11 on: February 03, 2025, 01:03:45 PM »
Randy the only thing that was diffrent was after you put in code wait until beep and then put in 111 and your code again it
worked for me


Bobby Kirk
2006 Marquis
The following users thanked this post: Randy Stephenson